C11 ACERT™ Dry Manifold Engine
Cat C11 ACERT engines are the ideal solution for your demanding operations in the oilfield. Decades of field operation and intense research and development allow Cat C11 ACERT engines to deliver excellent performance with low operating costs and emissions. Equipment powered by C11 ACERT engines include workover rigs, pump skids, acidizing units, cementing units, and hydraulic power units. Cat engines are backed by the worldwide network of Cat dealers ready to support your operation with technical support, service, parts, and warranty. C11 ACERT engines, with ratings: 242-336 bkW (325-450 bhp) @ 1800-2100 rpm, meet China Stage II, EPA Tier 3 equivalent, EU Stage IIIA equivalent emission standards. They are available using U.S. EPA and EU Flexibility, and for other regulated and non-regulated areas.
General Specifications
Maximum Rating
Displacement
Minimum Rating
Governor and Protection
Aspiration
Flywheel and Flywheel Housing
Flywheel Teeth
Rotation from Flywheel End
Stroke
Bore
Emissions
Emissions
Dimensions
Length
Width
Height
Weight
Capacity for Liquids
Lube Oil System - Refill
Standard Equipment:
-
- Air Inlet System
-
- Turbocharger, mid-mounted
- Air inlet elbow 90°, 104.5 mm (4.11" OD) hose connection
-
- Control System
-
- Electronic governing, PTO speed control
- Programmable ratings
- Cold mode start strategy
- Automatic altitude compensation
- Power compensation for fuel temperature
- Programmable low and high idle and TEL
- Electronic diagnostics and fault logging
- Engine monitoring system — speed, temperature, pressure
- J1939 Broadcast — diagnostic and engine status
-
- Cooling System
-
- Thermostats and housing
- Jacket water pump — gear-driven
- Front water pump inlet
-
- Exhaust System
-
- Exhaust manifold — dry
- Front turbo exhaust
-
- Flywheels And Flywheel Housings
-
- See Mandatory Options
-
- Fuel System
-
- Electronic unit injector
- Fuel filter — secondary, mid-mount, (LH 2 micron high performance)
- Fuel transfer pump — front
- Fuel priming pump — LH mid-mount
-
- Lube System
-
- Crankcase breather
- Oil cooler
- Oil filter — RH
- Oil pan — front sump, 40 L capacity
- Oil filler — LH front
- Oil dipstick — LH mid-mount
- Oil pump
- Oil valve sampling — on oil filter base
-
- Power Take-offs
-
- Crankshaft pulley and damper — 250 mm (9.84 in), 2 grooves 22.3 mm (.87 in) width
- Hydraulic pump drive — SAE A, 11 tooth
- 1.41:1 drive ratio — counterclockwise rotation (45 lb-ft capacity)
-
- General
-
- Vibration damper
- Paint — Cat yellow
- Lifting eyes
- Automatic variable timing, electronic
- Electronic installation kit (connectors, pins, sockets)
- Literature
-
- Mandatory Options
-
- Flywheel housing or rear PTO
- Throttle position sensor
- Primary filter/water separator
Optional Equipment:
-
- Air Compressor
-
- Expansion chamber
- Governors
- Fittings
-
- Air Inlet System
-
- Air cleaners
- Precleaners
- Turbo air inlet
- Air lines
-
- Belt-driven Accessories
-
- Refrigerant compressor and mounting
-
- Charging System
-
- Charging alternators
- Alternator mountings
- Alternator guard
- Alternator accessories
-
- Control System
-
- Connection
-
- Cooling System
-
- Radiator — installed
- Fan drive f/u/w Caterpillar installed radiator
- Fan drive pulleys f/u/w customer-supplied radiators
- Coolant conditioner
- Water lines — pump inlet
- Fan drive mountings
- Fan height instructions
- Fan adapters for suction fans
- Fan adapters for blower fans
- Suction fans
- Blower fans
- Coolant level sensor
- Aftercooler lines
-
- Exhaust System
-
- Muffler
- Flexible fitting
- Elbows
- Straight exhaust adapter
- Flange
- Pipe
- Rain cap
- Clamp
-
- Fuel System
-
- Fuel lines
- Fuel cooler
- Fuel fitting — fuel return and supply connections
- Flexible fuel lines
-
- Instrumentation
-
- Gauges and instrument panels
- Voltmeters
- Gauge mounting
- Ammeter
-
- Lube System
-
- Oil pan
- Oil pan drain
- Oil level gauges
- Oil filter — bypass
- Oil filter — remote
- Lubricating oil
- Oil filler
- Fumes disposal
-
- Mounting System
-
- Front and rear engine supports
- Structural steel base
-
- Power Take-offs
-
- Crankshaft pulleys
- Crankshaft pulley — stack-on
- Output flange
- Flywheel stub shaft
- Front stub shaft
- Hydraulic pump drive
- Hydraulic pumps — front
- Hydraulic pumps — rear
- Enclosed Clutch
- Clutch Support
-
- Protection System
-
- Air shutoff
- Air shutoff switch
-
- Starting System
-
- Electric starting motors — 12 Volt, 24 Volt
- Starting aids
- Battery sets — 24 Volt, dry
- Battery cable
- Battery rack
-
- Transmission Arrangement
-
- Transmission cooler
Contact Us
Get A Quote
Thank you for your interest in Mustang Cat. We are here to help you in any way that we can. If you have a question, need equipment advice or just need additional information, we want to hear from you. You can email, phone or fill out the form below and we will be happy to connect with you.