C7 ACERT™ Dry Manifold Engine
Cat C7 ACERT engines are the ideal solution for your demanding operations in the oilfield. Decades of field operation and intense research and development allow Cat C7 ACERT engines to deliver excellent performance with low operating costs and emissions. Applications powered by C7 ACERT engines include pump skids, acidizing units, cementing units, coil tubing units, and hydraulic power units. Cat engines are backed by the worldwide network of Cat dealers ready to support your operation with technical support, service, parts, and warranty. The C7 ACERT engines, with ratings: 168-224 bkW (225-300 bhp) @ 1800-2200 rpm, meet China Stage II, EPA Tier 3 equivalent, EU Stage IIIA equivalent emission standards. They are available using U.S. EPA and EU Flexibility, and for other regulated and non-regulated areas.
General Specifications
Maximum Rating
Displacement
Minimum Rating
Governor and Protection
Aspiration
Flywheel and Flywheel Housing
Flywheel Teeth
Rotation from Flywheel End
Stroke
Bore
Emissions
Emissions
Dimensions
Length
Width
Height
Weight
Capacity for Liquids
Lube Oil System - Refill
Standard Equipment:
-
- Air Inlet System
-
- Turbocharger, air to air aftercooled
- Air inlet, LH side facing front 79.0 mm (3.11 in) connection
-
- Control System
-
- Electronic governing, PTO speed control
- Programmable rating
- Cold mode start strategy
- Automatic altitude compensation
- Power compensation for fuel temperature
- Programmable low and high idle and TEL
- Electronic diagnostics and fault logging
- Programmable monitoring system (engine speeds, temperature, pressure)
- J1939 broadcast (diagnostic and engine status)
- Automatic variable timing, electronic
- All engines shipped at max rated rpm
-
- Cooling System
-
- Thermostats and housing, vertical outlet
- Jacket water pump — belt-driven, centrifugal
- Water pump, inlet RH front vertical inlet (pointing down)
-
- Exhaust System
-
- Exhaust manifold — dry
- Front turbo exhaust
-
- Fuel System
-
- Hydraulic Electronic Unit injection (HEUI)
- Fuel filter — secondary, LH front (2-micron high performance)
- Fuel transfer pump — LH front
- Fuel priming pump — LH front
-
- General
-
- Vibration damper
- Paint — Cat yellow
- Lifting eyes
- Electronic installation kit (connectors, pins, sockets)
-
- Lube System
-
- Crankcase breather, LH side
- Oil cooler, RH
- Oil filler, front top valve cover
- Oil filter and sampling valve, RH
- Oil pan, front sump, 31 L (33 qt) oil change capacity
- Oil dipstick, LH rear
- Engine oil pump (gear-driven)
- Engine shipped without oil
-
- Power Take-offs
-
- Crankshaft drive pulley — 2 grooves, 190 mm (7.5 in) diameter, 22.3 mm (0.88 in) wide
Optional Equipment:
-
- Air Compressor
-
- Air compressors
- Air compressor governor
-
- Air Inlet System
-
- Air cleaners
- Precleaner
- Air inlet elbow
- Air shutoffs
-
- Charging Systems
-
- Charging alternators
- Alternator mountings
- Alternator belt tensioner
- Alternator pulleys
- Alternator guards
-
- Cooling System
-
- Radiators
- Fan drive and pulley - f/u/w radiator packages
- Fans f/u/w radiator packages
- Coolant level sensor
- Fan drive mountings
- Fan adapters
- Fan adapter for blower fans
- Fan pulleys
- Fan height instructions
- Vee belts for customer-supplied radiators
- Suction fans and blower fans
- Water inlet elbows
- Dry charge coolant conditioners
-
- Emissions Certification
-
- IMO Certification
-
- Exhaust System
-
- Flexible fitting
- Turbocharger exhaust outlet adapters
- Elbows, flange, pipes, clamp
- Rain caps
- Manifolds
- Mufflers
-
- Flywheels And Flywheel Housing
-
- Crankshaft seal
-
- Fuel System
-
- Flexible fuel lines
- Water separator and fuel filters
- Fuel cooler
-
- General
-
- Tool set
-
- Instrumentation
-
- Gauges and instrument panels
- Interconnect harnesses
- Voltmeters
- Gauge mounting
- Ammeter
-
- Lube System
-
- Oil pan
- Drain and cover
- Oil level gauges
- Remote oil filter
- Oil fillers
- Lubricating oil
- Fumes disposal
-
- Mounting System
-
- Structural steel base
- Front engine support
- Rear engine supports
-
- Power Take-offs
-
- Enclosed clutch
- Clutch supports
- Flywheel stub shaft
- Hydraulic pump drives
- Hydraulic gear pumps
-
- Starting System
-
- Starting Aids
- Electric Starting Motors — 12V and 24V
- Battery Sets - 12V and 24V (dry)
- Battery Cable
Contact Us
Get A Quote
Thank you for your interest in Mustang Cat. We are here to help you in any way that we can. If you have a question, need equipment advice or just need additional information, we want to hear from you. You can email, phone or fill out the form below and we will be happy to connect with you.